Code No. P0137: Oxygen Sensor (rear) Circuit Low Voltage


OPERATION



  • The sensor signal is inputted to the engine-ECU connector terminal O2RL from the oxygen sensor (rear) output terminal.
  • The oxygen sensor (rear) connector terminal is earthed with engine-ECU connector terminal ORLE.

FUNCTION



  • The oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
  • When the air-fuel ratio is richer than the theoretical air-fuel ratio, the oxygen sensor (rear) sends a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it sends a voltage of about 0 V.
  • In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.

TROUBLE JUDGMENT


Check Conditions
  • Oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
  • Battery positive voltage is more than 11 V and is less than 16.5 V.
  • More than 5 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
  • Oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.

FAIL-SAFE AND BACKUP FUNCTION



  • None

PROBABLE CAUSES



  • Failed oxygen sensor (rear)
  • Open/short circuit or harness damage in oxygen sensor (rear) circuit or loose connector contact
  • Failed engine-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III data list

  • Data list reference table (Refer to ).

  1. Item AD: Oxygen sensor (rear)

Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Go to Step 2.

STEP 2. Perform voltage measurement at oxygen sensor (rear) connector.

  • Disconnect connector, and measure at harness side.
  • Ignition switch: "ON"
  • Voltage between terminal engine-ECU ORLE line and body earth.
OK: 0.4 - 0.6 V

Q. Is the check result normal?
Go to Step 5.
Go to Step 3.

STEP 3. Check harness between oxygen sensor (rear) connector terminal and engine-ECU connector terminal ORLE.

  • Check earthing line for open circuit.

Q. Is the check result normal?
Go to Step 4.
Repair or replace the connector, or repair the damaged harness wire.

STEP 4. M.U.T.-III data list

  • Data list reference table (Refer to ).

  1. Item AD: Oxygen sensor (rear)

Q. Is the check result normal?
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
Replace the engine-ECU.

STEP 5. Check harness between oxygen sensor (rear) connector terminal and engine-ECU connector terminal ORLE.

  • Check earthing line for damage.

Q. Is the check result normal?
Go to Step 6.
Repair or replace the connector, or repair the damaged harness wire.

STEP 6. Perform voltage measurement at oxygen sensor (rear) connector.

  • Use special tool test harness (MB991658) to connect connector, and measure at pick-up harness.
  • Transmission: 2nd speed
  • Drive with wide open throttle
  • Engine: 3,500 r/min or more
  • Voltage between terminal engine-ECU O2RL line and body earth.
OK:
    The output voltage should be 1.1 - 1.5 V.

Q. Is the check result normal?
Go to Step 8.
Go to Step 7.

STEP 7. Check oxygen sensor (rear) itself.



  • Oxygen sensor check (Refer to ).

Q. Is the check result normal?

    Repair or replace the connector, or check intermediate connectors, and repair if necessary. If intermediate connectors are normal, check and repair harness between oxygen sensor (rear) connector terminal and engine-ECU connector terminal O2RL.

    • Check output line for short circuit.
Replace oxygen sensor (rear).

STEP 8. Check harness between oxygen sensor (rear) connector terminal and engine-ECU connector terminal O2RL.

  • Check output line for open circuit and damage.

Q. Is the check result normal?
Go to Step 4.
Repair the damaged harness wire.